NSE7_EFW-7.0 Certification – Valid Exam Dumps Questions Study Guide! (Updated 122 Questions)
NSE7_EFW-7.0 Dumps are Available for Instant Access using 2Pass4sure
NEW QUESTION 56
Examine the output from the 'diagnose vpn tunnel list' command shown in the exhibit; then answer the question below.
Which command can be used to sniffer the ESP traffic for the VPN DialUP_0?
- A. diagnose sniffer packet any 'esp'
- B. diagnose sniffer packet any 'host 10.0.10.10'
- C. diagnose sniffer packet any 'port 4500'
- D. diagnose sniffer packet any 'port 500'
Answer: C
NEW QUESTION 57
View the exhibit, which contains the partial output of an IKE real time debug, and then answer the question below.
The administrator does not have access to the remote gateway.
Based on the debug output, what configuration changes can the administrator make to the local gateway to resolve the phase 1 negotiation error?
- A. Change phase 1 encryption to 3DES and authentication to SHA256.
- B. Change phase 1 encryption to AES128 and authentication to SHA512.
- C. Change phase 1 encryption to AESCBC and authentication to SHA128.
- D. Change phase 1 encryption to 3DES and authentication to CBC.
Answer: D
NEW QUESTION 58
Refer to the exhibit, which contains the partial output of the get vpn ipsec tunnel details command.
Based on the output, which two statements are correct? (Choose two.)
- A. Hub2Spoke1 is a policy-based VPN.
- B. Hub2Spoke1 is configured on interface wan2.
- C. Anti-replay is disabled.
- D. Phase 2 authentication is set to sha1 on both sides.
Answer: B,D
NEW QUESTION 59
Examine the output of the 'get router info ospf interface' command shown in the exhibit; then answer the question below.
Which statements are true regarding the above output? (Choose two.)
- A. The local FortiGate has been elected as the OSPF backup designated router.
- B. The port4 interface is connected to the OSPF backbone area.
- C. Two OSPF routers are down in the port4 network.
- D. There are at least 5 OSPF routers connected to the port4 network.
Answer: B,D
NEW QUESTION 60
Which of the following statements is true regarding a FortiGate configured as an explicit web proxy?
- A. FortiGate limits the number of simultaneous sessions per explicit web proxy user The limit CAN be modified by the administrator
- B. FortiGate limits the number of simultaneous sessions per explicit web proxy user. This limit CANNOT be modified by the administrator.
- C. FortiGate limits the number of workstations that authenticate using the same web proxy user credentials. This limit CANNOT be modified by the administrator.
- D. FortiGate limits the total number of simultaneous explicit web proxy users.
Answer: D
NEW QUESTION 61
An administrator wants to capture ESP traffic between two FortiGates using the built-in sniffer.
If the administrator knows that there is no NAT device located between both FortiGates, what command should the administrator execute?
- A. diagnose sniffer packet any 'udp port 500 or udp port 4500'
- B. diagnose sniffer packet any 'udp port 500'
- C. diagnose sniffer packet any 'esp'
- D. diagnose sniffer packet any 'udp port 4500'
Answer: C
NEW QUESTION 62
An administrator cannot connect to the GIU of a FortiGate unit with the IP address 10.0.1.254. The administrator runs the debug flow while attempting the connection using HTTP.
The output of the debug flow is shown in the exhibit:
Based on the error displayed by the debug flow, which are valid reasons for this problem? (Choose two.)
- A. HTTP administrative access is configured with a port number different than 80.
- B. HTTP administrative access is disabled in the FortiGate interface with the IP address 10.0.1.254.
- C. The packet is denied because of reverse path forwarding check.
- D. Redirection of HTTP to HTTPS administrative access is disabled.
Answer: A,B
NEW QUESTION 63
An administrator added the following Ipsec VPN to a FortiGate configuration:
configvpn ipsec phasel -interface
edit "RemoteSite"
set type dynamic
set interface "portl"
set mode main
set psksecret ENC LCVkCiK2E2PhVUzZe
next
end
config vpn ipsec phase2-interface
edit "RemoteSite"
set phasel name "RemoteSite"
set proposal 3des-sha256
next
end
However, the phase 1 negotiation is failing. The administrator executed the IKF real time debug while attempting the Ipsec connection.
The output is shown in the exhibit.
What is causing the IPsec problem in the phase 1?
- A. NAT-T settings do not match
- B. The incoming IPsec connection is matching the wrong VPN configuration
- C. The phrase-1 mode must be changed to aggressive
- D. The pre-shared key is wrong
Answer: D
NEW QUESTION 64
View the exhibit, which contains the partial output of a diagnose command, and then answer the question below.
Based on the output, which of the following statements is correct?
- A. Remote gateway IP is 10.200.5.1.
- B. Quick mode selectors are disabled.
- C. DPD is disabled.
- D. Anti-reply is enabled.
Answer: D
NEW QUESTION 65
Examine the output of the 'get router info bgp summary' command shown in the exhibit; then answer the question below.
Which statement can explain why the state of the remote BGP peer 10.200.3.1 is Connect?
- A. The local peer is receiving the BGP keepalives from the remote peer but it has not received any BGP prefix yet.
- B. The local peer is receiving the BGP keepalives from the remote peer but it has not received the OpenConfirm yet.
- C. The TCP session for the BGP connection to 10.200.3.1 is down.
- D. The local peer has received the BGP prefixed from the remote peer.
Answer: C
NEW QUESTION 66
When using the SSL certificate inspection method to inspect HTTPS traffic, how does FortiGate filter web requests when the client browser does not provide the server name indication (SNI) extension?
- A. FortiGate switches to the full SSL inspection method to decrypt the data.
- B. FortiGate uses the CN information from the Subject field in the server certificate.
- C. FortiGate blocks the request without any further inspection.
- D. FortiGate uses the requested URL from the user's web browser.
Answer: B
NEW QUESTION 67
An administrator has configured the following CLI script on FortiManager, which failed to apply any changes to the managed device after being executed.
Why didn't the script make any changes to the managed device?
- A. CLI scripts will add objects only if they are referenced by policies.
- B. Commands that start with the # sign are not executed.
- C. Static routes can only be added using TCL scripts.
- D. Incomplete commands are ignored in CLI scripts.
Answer: B
NEW QUESTION 68
View the exhibit, which contains a session entry, and then answer the question below.
Which statement is correct regarding this session?
- A. It is an ICMP session from 10.1.10.10 to 10.200.5.1.
- B. It is a TCP session in CLOSE_WAIT state from 10.1.10.10 to 10.200.1.1.
- C. It is an ICMP session from 10.1.10.10 to 10.200.1.1.
- D. It is a TCP session in ESTABLISHED state from 10.1.10.10 to 10.200.5.1.
Answer: A
NEW QUESTION 69
Examine the partial output from two web filter debug commands; then answer the question below:
Based on the above outputs, which is the FortiGuard web filter category for the web site www.fgt99.com?
- A. Information technology.
- B. General organization.
- C. Finance and banking
- D. Business.
Answer: D
NEW QUESTION 70
Examine the output from the 'diagnose vpn tunnel list' command shown in the exhibit; then answer the question below.
Which command can be used to sniffer the ESP traffic for the VPN DialUP_0?
- A. diagnose sniffer packet any 'esp'
- B. diagnose sniffer packet any 'host 10.0.10.10'
- C. diagnose sniffer packet any 'port 4500'
- D. diagnose sniffer packet any 'port 500'
Answer: C
NEW QUESTION 71
Examine the following routing table and BGP configuration; then answer the question below.
The BGP connection is up, but the local peer is NOT advertising the prefix 192.168.1.0/24 .
Which configuration change will make the local peer advertise this prefix?
- A. Enable the redistribution of static routers into BGP.
- B. Enable the redistribution of connected routers into BGP.
- C. Disable the setting network-import-check.
- D. Enable the setting ebgp-multipath.
Answer: C
NEW QUESTION 72
Examine the IPsec configuration shown in the exhibit; then answer the question below.
An administrator wants to monitor the VPN by enabling the IKE real time debug using these commands:
diagnose vpn ike log-filter src-addr4 10.0.10.1
diagnose debug application ike -1
diagnose debug enable
The VPN is currently up, there is no traffic crossing the tunnel and DPD packets are being interchanged between both IPsec gateways. However, the IKE real time debug does NOT show any output .
Why isn't there any output?
- A. The IKE real time debug shows the phase 1 negotiation only. For information after that, the administrator must use the IPsec real time debug instead: diagnose debug application ipsec -1.
- B. The IKE real time shows the phases 1 and 2 negotiations only. It does not show any more output once the tunnel is up.
- C. The IKE real time debug shows error messages only. If it does not provide any output, it indicates that the tunnel is operating normally.
- D. The log-filter setting is set incorrectly. The VPN's traffic does not match this filter.
Answer: D
NEW QUESTION 73
Examine the output of the 'diagnose debug rating' command shown in the exhibit; then answer the question below.
Which statement are true regarding the output in the exhibit? (Choose two.)
- A. A server's round trip delay (RTT) is not used to calculate its weight.
- B. The TZ value represents the delta between each FortiGuard server's time zone and the FortiGate's time zone.
- C. FortiGate will send the FortiGuard queries to the server with highest weight.
- D. There are three FortiGuard servers that are not responding to the queries sent by the FortiGate.
Answer: B,C
NEW QUESTION 74
View the exhibit, which contains the output of a diagnose command, and the answer the question below.
Which statements are true regarding the Weight value?
- A. Its initial value is calculated based on the round trip delay (RTT).
- B. Its initial value is statically set to 10.
- C. It determines which FortiGuard server is used for license validation.
- D. Its value is incremented with each packet lost.
Answer: D
NEW QUESTION 75
An administrator has configured the following CLI script on FortiManager, which failed to apply any changes to the managed device after being executed.
Why didn't the script make any changes to the managed device?
- A. CLI scripts will add objects only if they are referenced by policies.
- B. Commands that start with the # sign are not executed.
- C. Static routes can only be added using TCL scripts.
- D. Incomplete commands are ignored in CLI scripts.
Answer: B
NEW QUESTION 76
View the exhibit, which contains a screenshot of some phase-1 settings, and then answer the question below.
The VPN is up, and DPD packets are being exchanged between both IPsec gateways; however, traffic cannot pass through the tunnel.
To diagnose, the administrator enters these CLI commands:
However, the IKE real time debug does not show any output .
Why ?
- A. The log-filter setting was set incorrectly. The VPN's traffic does not match this filter.
- B. The debug output shows phases 1 and 2 negotiations only. Once the tunnel is up, it does not show any more output.
- C. The debug shows only error messages. If there is no output, then the tunnel is operating normally.
- D. The debug output shows phase 1 negotiation only. After that, the administrator must enable the following real time debug: diagnose debug application ipsec -1.
Answer: A
NEW QUESTION 77
View the exhibit, which contains the partial output of an IKE real-time debug, and then answer the question below.
Why didn't the tunnel come up?
- A. The remote gateway's phase 2 configuration does not match the local gateway's phase 2 configuration.
- B. The remote gateway is using aggressive mode and the local gateway is configured to use man mode.
- C. The remote gateway's phase 1 configuration does not match the local gateway's phase 1 configuration.
- D. The pre-shared keys do not match.
Answer: C
NEW QUESTION 78
What conditions are required for two FortiGate devices to form an OSPF adjacency? (Choose three.)
- A. OSPF costs match.
- B. OSPF IP MTUs match.
- C. OSPF peer IDs match.
- D. Hello and dead intervals match.
- E. IP addresses are in the same subnet.
Answer: B,D,E
NEW QUESTION 79
Examine the following traffic log; then answer the question below.
date-20xx-02-01 time=19:52:01 devname=master device_id="xxxxxxx"
log_id=0100020007 type=event subtype=system pri critical vd=root service=kemel status=failure msg="NAT port is exhausted."
What does the log mean?
- A. There is not enough available memory in the system to create a new entry in the NAT port table.
- B. FortiGate does not have any available NAT port for a new connection.
- C. The limit for the maximum number of entries in the NAT port table has been reached.
- D. The limit for the maximum number of simultaneous sessions sharing the same NAT port has been reached.
Answer: D
NEW QUESTION 80
An administrator cannot connect to the GIU of a FortiGate unit with the IP address 10.0.1.254. The administrator runs the debug flow while attempting the connection using HTTP.
The output of the debug flow is shown in the exhibit:
Based on the error displayed by the debug flow, which are valid reasons for this problem? (Choose two.)
- A. HTTP administrative access is configured with a port number different than 80.
- B. HTTP administrative access is disabled in the FortiGate interface with the IP address 10.0.1.254.
- C. The packet is denied because of reverse path forwarding check.
- D. Redirection of HTTP to HTTPS administrative access is disabled.
Answer: A,B
NEW QUESTION 81
......
Fortinet NSE7_EFW-7.0 Exam Practice Test Questions: https://www.2pass4sure.com/NSE-7-Network-Security-Architect/NSE7_EFW-7.0-actual-exam-braindumps.html
NSE7_EFW-7.0 Dumps 2023 - New Fortinet NSE7_EFW-7.0 Exam Questions: https://drive.google.com/open?id=1YO4NJHjpca2cK9HXKlJxzr24Gk1SEBPH